中国铁路提速后技术进步对产出贡献的测算

选取我国铁路提速后1997~2007年间的相关数据,采用基于科布——道格拉斯生产函数的Solow余值法,将有限分布滞后模型和半参数回归模型引入计算模型,对数据进行拟合,计算得到铁路提速后技术进步、固定资本投入以及人力资本投入对产出的贡献率,并根据计算结果提出促进我国高速铁路建设的相关对策建议.     

非线性混合海况下近海风机塔筒底部载荷的动力响应

本文主要研究在非线性混合海况(即风浪和涌浪组合海况)下,以NREL 5MW_Baseline Monopile近海风机为研究对象,对其塔筒底部(基线)所受到的剪力和弯矩载荷的动力响应进行仿真。在近海风机的时域仿真中,选用了Ochi-Hubble六参数波浪谱,并编制了该谱的程序嵌入到FAST中进行编译。计算过程中,共进行了20次10 min的仿真分析。对于得到的短期载荷,给出了波高程,塔筒底部首尾向剪力和弯矩在线性与非线性不规则波作用下的时程曲线对比图。采用分块最大值法对每一次的短期载荷提取极值,并基于20次仿真所得的极值,给出了塔筒底部首尾向剪力与弯矩在线性与非线性不规则波作用下的超越概率曲线对比图。研究表明,在非线性混合海况下进行近海风机塔筒底部载荷的动力响应研究,计算结果对工程实际应用具有指导意义。     

On the fluid-structure response of elastic-plastic ship sides subjected to impact loads

This paper presents a simplified numerical model capable of analysing the interaction between the structural dynamic response of elastic-plastic struck plate wall of a fluid tank subjected to wedge impact and the resulting fluid motion. The Variational Finite Difference Method (VFDM) is applied to analyse the structural dynamics of the struck plate and 2-D linear potential flow theory is used to study the resulting fluid motion and its effects on the structural dynamics of the struck plate. Experiments of a wedge indenter impacting with both empty and 90% filled tanks are carried out to study the structural deformation of the struck plate. The accuracy of the developed numerical model is validated with published results and experimental results, and good agreement is achieved. Through the comparison of the impact behaviour of empty and partially filled water tank, it is found that the resulting water motion helps to reduce the structural deformation of the struck plate since part of the impact energy is dissipated by the resulting water motion. Parametric studies are performed to investigate the effect of impact velocity and water level on the structural dynamics of the struck plate of a partially filled water tank. A case study is also conducted to demonstrate the potential application of the proposed method in analysing ship-ice impact problems.     

一种特殊的电机启动方式在混合动力船舶的应用

混合动力船舶越来越多,本文主要介绍在混合动力船舶中推进电机的一款特殊启动方法,不需要额外添加任何的启动器,利用主柴油机来启动推进电机达到混合推进的目的     

基于轨道极限状态法的过渡板受力分析和配筋设计研究

京张高铁官厅水库特大桥为简支拱型大跨度钢桁梁桥,为防止梁端转角或错台量过大,降低梁端扣件系统受力,梁缝处设计采用了过渡板结构。为保证过渡板设计合理性和安全性,建立过渡板有限元实体模型进行受力分析,并首次运用轨道极限状态法对过渡板结构进行配筋设计。分析表明:(1)温度梯度作用对过渡板(420 mm厚)受力影响较大,在设计荷载中占据主导因素,在正温度梯度下,过渡板底部弯矩达到124.155 kN·m/m;(2)过渡板底部纵向弯矩在荷载基本组合作用下达到最大值,且实配配筋率最大,配筋时应注意以裂缝宽度为控制指标进行设计。     

Numerical study on the dynamic response of a truncated ship-hull structure under asymmetrical slamming

Dynamic response of ship-hull structure under slamming has tracked widespread attention in the marine structural design. However, our understanding on the dynamic characteristics largely relies on the symmetrical slamming cases. This paper presented a preliminary numerical investigation on the dynamic response of a truncated ship-hull structure under asymmetrical slamming based on the uncoupled CFD-FE method. Asymmetrical slamming loads were predicted through combining the seakeeping analysis and CFD method. In there, three kinds of motions (vertical, horizontal and roll motions) of 2D ship sections were obtained through the seakeeping analysis and then the slamming pressure was predicted through simulating the water entry with various motions based on CFD method. The dynamic response was analyzed through finite element method. Numerical predictions including ship motions, slamming loads and dynamic analysis were validated against published experimental data and numerical calculations. The characteristics of asymmetrical slamming loads were analyzed showing obvious asymmetry in space, and the dynamic characteristic of the ship bow structure was further clarified through discussing the deformation and stress distribution. These results are useful for readers for better understanding the dynamic characteristics of the bow structure under slamming.     

Simplified buckling-and-contact-based expansion method for assessment of crashworthiness of double-hulled ship structure

Ship-to-ship collision events can have severe consequences such as loss of life and environmental degradation. For this reason, modern ship designs are required to incorporate a double-hulled structure to prevent inner-hull damage from such events. Using the experimental or numerical method to analyze the crashworthiness of double-hulled ship structures entails much effort, for which reason neither method is easy to adopt at the early design stage. In this paper, an existing simplified method called Ito's method is improved by a new buckling-and-contact-based expansion method. This method can be applied to double-hulled-structure or outer-hull-local-rupture failure mode. The perpendicular bow-to-side collision scenario is assumed for a conservative estimation of damage to a double-hulled structure. The method was verified in the present study by numerical ship collision simulations of several cases. The results for the buckling-and-contact-based expansion method and numerical simulation were similar for a blunt shape of striking body but different for a sharp shape.     

表面选区强化对钢轨波磨处轮轨滚动接触行为的影响

层流等离子体表面强化技术可大幅提高钢轨表面的硬度和耐磨性。为了揭示强化处理对轮轨滚动接触行为的影响,建立同时考虑钢轨表面选区强化和短波波磨的三维轮轨瞬态滚动接触有限元模型,数值计算了车轮高速滚过一个波磨周期的轮轨力、接触斑黏滑分布和残余应力应变。对比发现:表面选区强化对轮轨力和接触斑黏滑分布的影响较小,不影响钢轨承载性能;对钢轨表面残余应力应变分布的影响明显,残余应力主要集中在屈服强度较高的强化斑内而残余应变主要集中在韧性较好的基体材料上,表面选区强化有效结合了强化斑和基体材料的力学性能,形成了一种强韧的良好匹配。结果可为现场生产服务提供一定的理论指导和应用参考。     

基于改进云模型的地铁站行人拥挤辨识方法

为降低城市地铁站内行人拥挤识别时多指标和多等级带来的不确定性和模糊性,采用改进云模型构建行人拥挤状态辨识模型。基于AHP-熵权法标定指标权重和行人拥挤状态等级,以标定的指标权重和各指标等级阈值作为输入,计算云数字特征值,采用正向正态云发生器,建立模板云和待识别云模型,计算两者之间的隶属度,根据最大隶属度原则辨识车站内各服务设施的行人拥挤状态,最后输出各服务设施的拥挤等级辨识结果。以宁波市鼓楼站为实证对象,对辨识结果进行实证分析。结果表明:采用四级行人拥挤状态划分方法合理可行。     

地铁隧道二次衬砌钢筋网防裂性能研究

为了定量分析防裂钢筋网提高隧道衬砌结构抗裂性能的机理和幅度,以地铁双线隧道二次衬砌结构为研究对象,采用荷载结构法和杆系有限元数值模拟方案,定量分析二次衬砌结构不设置与设置钢筋网这2种情况下的开裂临界荷载。其中素混凝土结构以达到极限拉应变为临界状态,衬砌结构增设钢筋网后以达到GB 50157-2013《地铁设计规范》允许的最大裂缝宽度0.2mm为临界状态。分析结果表明,配置防裂钢筋网后,Ⅲ级和Ⅳ级围岩衬砌结构抗裂性能可分别提高22.4%和19.3%,Ⅴ级围岩衬砌结构抗裂性能提高15.2%;Ⅲ级和Ⅳ级围岩二次衬砌结构的破坏形式由脆性破坏变为延性破坏,从而提高了其安全性能。